FAQ
Home > FAQ

Electrode Paste Consumption and Furnace Condition Control of Ferrosilicon Furnaces (72# / 75#)(2026 Edition)

Time:2026-10-30   Traffic:1133

Abstract

Ferrosilicon (FeSi) is the most typical slag-free smelting grade; 72# (about 72% Si) and 75# (about 75% Si) are the mainstream grades in China. The core contradiction in electrode management for ferrosilicon furnaces is not "under-baking" but "baking too fast and oxidizing too severely".

Keywords|Ferrosilicon (FeSi);slag-free smelting;electrode oxidation;oxidation resistance;electrode slipping;burden surface management;arc exposure;72# / 75# grades;electrode paste unit consumption;three-phase current balance

Last updated: 2026-10-30·Owner: Rongxing Group Technical Team

Content

1. How the process characteristics of ferrosilicon furnaces affect the electrode

CharacteristicImpact on the electrodeResponse direction
Slag-free smeltingNo slag layer covers the burden surface, so the upper part of the electrode is exposed to high-temperature furnace gasStrengthen burden surface maintenance (a problem that arises in open furnaces) to isolate air ingress as far as possible
Deep electrode insertionThe working end is buried in the burden layer, so the tip temperature is high and consumption is concentratedMaintain a reasonable insertion depth and avoid "arc exposure"
High furnace mouth temperatureThe side of the electrode oxidizes quickly and its diameter gradually thinsImprove the furnace-platform operating conditions and keep the electrode properly submerged in the arc
Carbon does not take part in the main reactionChemical consumption is lower than in silicomanganese, but mechanical and oxidation consumption account for a higher shareFocus on improving strength and oxidation resistance rather than simply raising the sintering speed

2. Consumption level and influencing factors

The general industry benchmark is that producing 1 tonne of ferrosilicon containing 75% silicon consumes about 45 kg of electrode paste. Actual values, however, vary greatly with furnace capacity and operating level: the common domestic operating range is 25–45 kg/t, and a well-managed large furnace can approach 30 kg/t or even lower.

Influencing factorDirectionExplanation
Ash content of electrode pasteAsh ↑ → unit consumption ↑Ash takes part in slag formation and accelerates tip consumption
Oxidation resistanceOxidation resistance ↑ → unit consumption ↓Graphite fines and low porosity can slow side oxidation
Electrode insertion depthToo shallow → unit consumption ↑Arc exposure causes simultaneous high-temperature oxidation of the tip and the side
Burden surface managementBurden surface collapse → unit consumption ↑The impact of a collapse causes block loss and breakage
Secondary currentToo high → unit consumption ↑Higher current density means faster tip erosion

3. Furnace condition control

"Stability" comes first: ferrosilicon furnaces dislike frequent adjustments. The unbalance of the three-phase current should be controlled within 5%; the burden surface should be kept "flat, full and loose", avoiding "sparking" (local arc exposure) and large burden collapses.

Matching electrode slipping with sintering: the electrode consumption rate of ferrosilicon furnaces is moderate, so the "small amount, many times" slipping principle should be followed. Each slip should preferably not exceed 100–150 mm, and after slipping one should observe for 2 h before deciding on the next slip. The daily slipping amount can serve as an indirect monitoring indicator of unit consumption.

Differences between 72# and 75#

GradeSilicon contentSmelting difficultyFocus of electrode management
72#About 72%Relatively easy, with a slightly lower furnace temperatureControl oxidation and stabilize the burden surface
75#About 75%Higher furnace temperature and more severe electrode erosionStrengthen oxidation resistance and strength; unit consumption is usually higher than that of 72#

PREVIOUS:What Are the Special Requirements of High-Carbon Ferrochrome Furnaces for Electrode Paste?(2026 Edition)

NEXT:Technical Requirements and Selection Recommendations for Electrode Paste in Calcium Carbide Furnaces

Honesty connects the whole world
Rongxing adheres to the business philosophy of sincerity. From strategy formulation to raw material procurement, business negotiations, and technical services, we never cheat.
公司Logo
  • Rongxing Group focuses on product quality and reputation. It is a group company integrating the production and operation of electrode paste and graphite electrodes.
公司Logo
Products
Connect
  • PhonePhone:+86 19937179450
  • WhatsappWhatsapp:+86 19937179450
  • EmailEmail:[email protected]
  • AddressAdd:Zhengdong New District,Zhengzhou City,China.
Email
Message
Whatsapp
TOP